LED Construction

Building Quality, Crafting Trust

Your Vision, Our Expertise.
Call Us Today
07512 399673

Block Paving Driveways in Kent

Block paving driveways give Kent homeowners a durable, practical surface with a choice in pattern, colour, edging, and finish. LED Construction installs block paving across Sittingbourne and Kent, starting with a free site survey and detailed estimate. We check the ground, drainage, excavation depth, MOT Type 1 sub-base, sharp sand bedding, edge restraints, and jointing before work begins. That preparation helps reduce the risk of sinking, cracking, puddling, and movement, leaving you with a driveway built to last for everyday vehicle use in Kent.

See More
Free Estimate

What Block Paving Is And How It Differs From The Alternatives

Block paving is made from individual concrete or clay blocks laid over a prepared sand bed and compacted sub-base. Unlike tarmac or resin, it is not one fixed surface, which makes repairs much easier. If one area moves, cracks, or needs access underneath, we can lift and replace the affected blocks without disturbing the rest of the driveway.

We can discuss suitable driveway patterns because pattern choice can affect stability under vehicle use. During the free site survey, we explain the pattern, colour, and edging options so you know what suits your property best.

Is Block Paving Right For Your Property?

Block paving suits most residential driveways in Kent, but the best outcome depends on the groundwork. A few things worth knowing before you decide:

  • Sub-base depth matters. Vehicle surfaces need a deeper MOT Type 1 sub-base than pedestrian areas. We dig to the correct depth for the load, not a standard number.
  • Drainage planning is part of the job. Block paving onto clay soil without addressing run-off can cause problems down the line. We assess drainage at the site survey.
  • Planning permission. Standard block paving over more than 5m² of front garden may require planning permission if it is impermeable and does not direct rainwater to a permeable area. Permeable block paving, with wider joints filled with grit, will usually avoid that requirement, as it allows water to drain through correctly. We can install either and advise which route makes sense for your project.
  • Existing ground conditions. Tree roots, old concrete bases, and soft spots under the topsoil all affect how much excavation is needed. We will not give a fixed price until we have seen the ground.

Tell us about your project?

Got plans in mind? Whether it’s a brand-new driveway, a fresh patio, or some expert brickwork, we’d love to hear all about it. Fill in the form below with a few details and we’ll get back to you as soon as we can to discuss your ideas, answer any questions, and provide a free, no-obligation quote.

This field is for validation purposes and should be left unchanged.
Accepted file types: jpg, gif, png, pdf, Max. file size: 20 MB.

What Block Paving Is And How It Differs From The Alternatives

Contemporary Block Paving Driveway

Block paving is made from individual concrete or clay blocks laid over a prepared sand bed and compacted sub-base. Unlike tarmac or resin, it is not one fixed surface, which makes repairs much easier. If one area moves, cracks, or needs access underneath, we can lift and replace the affected blocks without disturbing the rest of the driveway.

We can discuss suitable driveway patterns because pattern choice can affect stability under vehicle use. During the free site survey, we explain the pattern, colour, and edging options so you know what suits your property best.

Is Block Paving Right For Your Property?

Block paving suits most residential driveways in Kent, but the best outcome depends on the groundwork. A few things worth knowing before you decide:

  • Sub-base depth matters. Vehicle surfaces need a deeper MOT Type 1 sub-base than pedestrian areas. We dig to the correct depth for the load, not a standard number.
  • Drainage planning is part of the job. Block paving onto clay soil without addressing run-off can cause problems down the line. We assess drainage at the site survey.
  • Planning permission. Standard block paving over more than 5m² of front garden may require planning permission if it is impermeable and does not direct rainwater to a permeable area. Permeable block paving, with wider joints filled with grit, will usually avoid that requirement, as it allows water to drain through correctly. We can install either and advise which route makes sense for your project.
  • Existing ground conditions. Tree roots, old concrete bases, and soft spots under the topsoil all affect how much excavation is needed. We will not give a fixed price until we have seen the ground.

Tell us about your project?

Got plans in mind? Whether it’s a brand-new driveway, a fresh patio, or some expert brickwork, we’d love to hear all about it. Fill in the form below with a few details and we’ll get back to you as soon as we can to discuss your ideas, answer any questions, and provide a free, no-obligation quote.

This field is for validation purposes and should be left unchanged.
Accepted file types: jpg, gif, png, pdf, Max. file size: 20 MB.

CALL US FREE FOR THE BEST POSSIBLE PRICE

07512 399673
Start Your Free Estimate
Contemporary Block Paving Driveway

How The Installation Runs, From Site Survey To Finished Surface

Every block paving driveway we install follows the same sequence. There are no shortcuts on the groundwork. That is where most failures start, and it is where we spend the most time.

  • Free site survey. We measure the area, check drainage, and look at the existing ground. You will know what is involved before any work is priced.
  • Full excavation. We dig to the depth required for the sub-base and bedding layer: deeper for vehicle surfaces, shallower for pedestrian areas.
  • MOT Type 1 sub-base. Crushed stone compacted in layers. This is the foundation. We do not reduce sub-base depth to cut costs.
  • Sharp sand bedding layer. Screeded flat and level before the blocks go down.
  • Block laying. Pattern confirmed at survey, blocks cut to fit at edges and around obstacles.
  • Edge restraints and kerbs. Concrete haunching holds the perimeter. Without it, blocks migrate outward over time.
  • Kiln-dried sand jointing. Brushed into the joints and vibratory-plate compacted.
  • Optional sealant. Locks the jointing sand and protects the colour. We discuss this at survey, not as a standard add-on.

Installation typically runs 4 to 7 working days, depending on area size and site complexity.

What Led Construction Will Not Do On A Block Paving Quote

We do not give phone prices on block paving. The ground conditions under a Kent driveway vary more than the surface suggests. You can have solid chalk six inches down in one street and heavy clay two roads over. A site visit helps us quote more accurately and avoid unnecessary changes later. Neither is a good outcome. We quote in writing after the free survey, and that is the price we work with.

We also do not reduce sub-base depth to sharpen a number. Block paving laid on an insufficient sub-base settles unevenly within a couple of winters. The repair cost overtakes any savings within five years. The installation spec we quote is the spec we deliver.

Get A Free Estimate

How The Installation Runs, From Site Survey To Finished Surface

Contemporary Block Paving Driveway

Every block paving driveway we install follows the same sequence. There are no shortcuts on the groundwork. That is where most failures start, and it is where we spend the most time.

  • Free site survey. We measure the area, check drainage, and look at the existing ground. You will know what is involved before any work is priced.
  • Full excavation. We dig to the depth required for the sub-base and bedding layer: deeper for vehicle surfaces, shallower for pedestrian areas.
  • MOT Type 1 sub-base. Crushed stone compacted in layers. This is the foundation. We do not reduce sub-base depth to cut costs.
  • Sharp sand bedding layer. Screeded flat and level before the blocks go down.
  • Block laying. Pattern confirmed at survey, blocks cut to fit at edges and around obstacles.
  • Edge restraints and kerbs. Concrete haunching holds the perimeter. Without it, blocks migrate outward over time.
  • Kiln-dried sand jointing. Brushed into the joints and vibratory-plate compacted.
  • Optional sealant. Locks the jointing sand and protects the colour. We discuss this at survey, not as a standard add-on.

Installation typically runs 4 to 7 working days, depending on area size and site complexity.

What Led Construction Will Not Do On A Block Paving Quote

We do not give phone prices on block paving. The ground conditions under a Kent driveway vary more than the surface suggests. You can have solid chalk six inches down in one street and heavy clay two roads over. A site visit helps us quote more accurately and avoid unnecessary changes later. Neither is a good outcome. We quote in writing after the free survey, and that is the price we work with.

We also do not reduce sub-base depth to sharpen a number. Block paving laid on an insufficient sub-base settles unevenly within a couple of winters. The repair cost overtakes any savings within five years. The installation spec we quote is the spec we deliver.

Get A Free Estimate

WHY CHOOSE LED Construction FOR YOUR Block Paving Driveways in Kent

A block paving driveway installed on the correct sub-base, with proper edge restraints and jointing, should last upwards of 20 years. The blocks themselves are rated for 30 or more years. What shortens that lifespan is sub-base failure (usually from inadequate depth or compaction), edge migration (missing or failing kerb haunching), and weed growth through the joints (which kiln-dried sand and good drainage minimise).

Kent’s clay-heavy ground adds one consideration: drainage. Where clay sits near the surface, and run-off is not managed, water retention under the sub-base causes frost heave in cold winters. We factor that into the drainage assessment at the survey. Driveways we install do not come back to us with frost heave problems because we look at the drainage before we price the job.

What Block Paving Costs At Led Construction, And How We Quote

Block paving is priced by area, block type, groundwork depth, and pattern complexity. We quote after the site survey, not before it. If you want a rough frame of reference, we can provide one after we have assessed the site and block specification. The final price shifts based on access, excavation depth, drainage requirements, and the block specification you choose.

What we quote covers the full job: excavation, sub-base, bedding, blocks, edge restraints, jointing sand, and final compaction. There are no line items added on the day. If the ground survey reveals something that changes the scope, a deeper dig or additional drainage work, we will tell you before we start, not after.

Free Estimate

Frequently Asked Questions

FAQ's About Block Paving Driveways in Kent

Does block paving need planning permission?
It depends on the size and drainage. If the front garden area is over 5m² and the paving is impermeable and does not direct rainwater to a permeable area, you may need planning permission. Permeable block paving, when installed to allow water to drain through correctly, will usually avoid that requirement. We advise on which approach suits your project at the survey.
How long will the installation take?
Most residential driveways take 4 to 7 working days from start to finish. That covers excavation, sub-base, block laying, edging, and jointing. Larger or more complex projects take longer. We will give you a realistic timeline at the quote stage, not a number designed to win the job.
What patterns do you offer?
For driveways, we typically recommend herringbone at 45 or 90 degrees. It is one of the strongest pattern options for vehicle loads because the interlocking angle resists movement under braking. Stretcher bond works well for paths and patio edges. We can also incorporate contrasting borders, circular features, and mixed-colour designs. Bring any inspiration to the survey, and we will tell you what is achievable on your plot.
Can individual blocks be replaced if they get damaged?
Yes. That is one of block paving's main practical advantages. Individual blocks lift out without disturbing the surrounding surface. For utility access or tree root repairs, this makes a meaningful difference. Keep a small quantity of your original blocks when we finish the job so you have a perfect match if you need a repair years later.
Do you seal the block paving after installation?
Sealing is optional, not standard. Sealant locks the jointing sand, resists oil and fuel stains, and can enhance the colour. It adds to the overall cost and needs reapplication every 5 to 10 years. We discuss it in the survey. Some clients prefer an unsealed finish, particularly where a more natural look fits the property.
What areas do you cover for block paving in Kent?
We are based in Sittingbourne and install block paving driveways across Kent: Sittingbourne, Faversham, Lynsted, Maidstone, Ashford, Canterbury, Medway, and Dover. If you are in a different part of Kent, give us a call, and we will let you know if we can get to you.